The Backcountry Backpack is a fully featured, large capacity pack designed for multi-day walks carrying expedition-size loads. The new Mont Backcountry Canvas Pack is available in 3 adjustable sizes depending on your height, and combines hardwearing construction, excellent weight dispersion and fine-tune adjustment for superior trail comfort.
The Backcountry is built from Infinity Corespun canvas, a highly durable poly/cotton fabric. The strength of the fabric is due to the composite yarn: a polyester core with cotton wrapped around it. The composite yarn base provides superior strength and unequalled performance. Once woven the fabric is treated with a wax based polymer for water resistance, anti-bacteria protection and UV stability.
Features
- Highly adjustable Moto Active Harness System available in 3 sizes
- Dual compartment with removable internal divider
- Zip access to lower compartment
- Body fit profile for load carrying comfort
- Expandable and removable lid with lightweight Nylon lid integrated into storm throat
- Front expandable pleated stuff pocket
- Dual vertical daisy chain webbing
- Dual side compression straps with side release buckles
- Pleated Canvas bottle pockets
- Canvas bound seams for greater water resistance
- Extendable lid to maximise packing space
- Single pull quick draw closure on Nylon storm throat
- Internal water bladder sleeve with hose exit ports for either shoulder strap
- Dual ice axe/walking pole attachment straps
- Front and rear packing/haul handles
- Contoured Shoulder Straps. Shoulder straps map the curves of your torso & provide stability & comfort on the longest of walks.
- Dual Vertical & Single Horizontal Hollow Core Stays. Weight is transferred directly to the hip-belt via two hollow-core aluminium stays. Hollow-core stays are 20% lighter & 25% stronger than previously used extruded aluminium stays.
- Multilayer Foam Hip Belt. Moto Active contoured hip-belt with 8 layer construction: open & closed cell foams, HTPE sheet & highly durable Cordura Nylon.
- V-Ridge Foam. Stay cooler with the ventilated, non-moisture-absorbing, V-Ridge Foam back panel.
- Single Point Adjustment. Adjust the back length with one simple change.
Specifications
- Capacity: 75-85 Litres
- Weight:3.15kg (medium)
- Harness Type: MotoActive Harness
- Fabric: Infinity Corespun Canvas / 470D Cordura Nylon
BACKPACK FITTING GUIDE
| HARNESS SIZE | X-SMALL | SMALL (75L) | MEDIUM (80L) | LARGE (85L) |
|---|---|---|---|---|
| BACK LENGTH (CM) | 35-45 | 40-50 | 45-55 | 50-60 |
| BACK LENGTH (INCH) | 13.5-17.5 | 15.5-19.5 | 17.5-21.5 | 19.5-23.5 |
FINDING YOUR BACK LENGTH
To determine your harness size you will need to know your back length. Measuring your back length is easy with the help of a friend.
Measure from your C7 vertebrae down your spine to the point level with the top of your hipbones, the iliac crest.
The C7 vertebrae is the one that sticks out prominently at the back of your neck when you tilt your head forward.
Once you know your harness size it is important to fit the pack correctly. A correctly fitted pack is essential for load carrying comfort.
- Put the pack on, loosen all of the straps and tighten the hip-belt until firm. The middle of the hip-belt pads should wrap snugly over your hips.
Next, tighten the shoulder straps under your arms, then the stabiliser straps between the tops of the shoulders and the top of the pack frame.
With the hip-belt hugging your hip bones the shoulder straps should wrap comfortably over your shoulders without excess pressure.
If the shoulder straps are too tight on your shoulders or sitting loosely above your shoulders, you will need to adjust the harness back length. This is done by tightening or loosening the webbing strap recessed between the shoulder straps at the top of the harness.
For previous model MotoActive and NovoLite harnesses the back length is adjustment is above the lumbar pad or recessed beside the lumbar pad and behind a hip belt.
The curvature of the stays may also need adjusting. Inside the pack is a flap covering the top of the aluminium stay/s. Pull back the flap, pull out the stay and shape it to fit.
Finally, tighten the stabiliser straps between the hip-belt and the base of the pack.
With light to moderate loads you may not need to use the sternum strap, but for heavy loads the sternum strap will provide extra stability.
The best way to evaluate your harness fitting is to load the pack up with about 12kg and go for a wander. A correctly fitted pack will distribute a majority of the weight comfortably on your hips via the hip-belt, the shoulder straps are largely for stability.
